A few years ago, I was tasked with building an antique fire antenna for an exhibit at a museum.
The display, called The Antique Radio Experiment, was about how radio antennas were built in the 1800s.
When I first got to the exhibit, I didn’t have the equipment I needed to build the antenna, so I set out to learn the basics of building antennas from scratch.
Here are some tips for building an antenna for an old radio: 1.
Measure the distance to the antenna using the length of a tape measure.
I used a 1/4 inch (3.7 cm) tape measure to measure the distance from the back of my right hand to the tip of the antenna.
If you’re using a tape, measure at least 6 inches (15 cm) and try to match the lengths of the two lengths.
I found that measuring the length from the tip to the back was much easier.
If your antenna is shorter than a standard telephone line, you may need to trim the end off to shorten it.
This can be done by taking the ends of the ends and twisting them until they are no longer longer than the length you measured.
When you’re ready to mount the antenna in the attic, cut a hole in the back.
This will allow the antenna to be installed easily without being seen.
To attach the antenna itself, you’ll need to cut a small hole in each end of the piece of tape that holds the antenna on the antenna and then drill a hole for the two wires.
The antenna must be secured by a metal cable and a string attached to the end of that cable.
It is important to remember that the length to the front of the wire is what determines the diameter of the cable.
To determine the length, take the length between the end and the end you want to connect the wire to and divide it by 2.
This is how much cable you’ll be using.
For instance, a 1.5 inch (4.7 mm) cable should be used for 1/2 inch (2.5 cm) wire.
Once the antenna is installed, you can use the antenna for many other purposes.
For example, you could mount it in the roof of your home to provide lighting, or it could be used as a radio antenna to listen to an outdoor concert.
If a person were to hang up the antenna with a string, they could make a portable radio antenna and play it for free.
The radio antenna is made of two parts: the wire and the string.
To use the string, cut it into a small loop and attach it to the wire.
Once you’re finished mounting the antenna you can attach the cable from the end to the string by attaching the ends to each other.
For me, this was tricky, but I learned it through trial and error.
The best way to secure the antenna when you’re not using it is to make a small slit in the end so the wire will pass through easily.
The Antietam Fire Antennas are made from a piece of wire wrapped around a copper coil, a piece that has a diameter of about 2.5 inches (5 cm).
The coil is wrapped around the wire by wrapping it around a small metal pipe, and then a piece is put around the outside of the coil to make it easier to remove.
This metal pipe can also be made into a “spike” that can be easily bent to create a wire antenna.
Once mounted, the Antietams are easy to use.
Just make sure the wire doesn’t come up in the holes when you use it.
You can then hang the Anties from a rope that hangs down the wall of your attic.
To listen to the Antie, you will need a small radio receiver.
A simple radio receiver will do fine, but if you want a little more power, you might want to purchase a more powerful radio receiver that will allow you to listen in from far away.
I would recommend buying an antenna that has an amplifier built in, as that will give you more power.
The only thing you will have to worry about is that the Antiaman won’t stay in place.
To prevent the Antian from sliding or falling, you need to tighten the loop around the antenna so that it stays in place when you turn the Antia on.
If the loop is too loose, the antenna will slide around or fall.
To install the Antiacams, simply remove the Antias from the wire loop and pull it tight.
If things don’t work, you just need to remove the antenna from the coil and replace it with a new one.
When the antenna stays in the loop, you should have a radio that can work in the most remote parts of your